What the code means
E3.3: Shorted second-stage pressure switch
The Trane S9V2 Link-enabled operation alarm table identifies E3.3 as a shorted second-stage pressure switch.
Troubleshooting code
Back to all S9V2 96 Two-Stage Variable Speed Gas Furnace error codes
Trane S9V2 96 Two-Stage Variable Speed Gas Furnace E3.3 troubleshooting
Shorted second-stage pressure switch. Use this page to document the issue and prepare for service. GreenFlow should handle diagnosis for electrical, refrigerant, lockout, or recurring conditions.
Safe checks before calling
- Confirm the thermostat is on, set correctly, and calling for heating or cooling.
- Check the air filter and visible return-air path for obvious airflow restrictions.
- Look around the outdoor unit for leaves, snow, ice, or other visible obstructions without opening the cabinet.
- Take photos of the thermostat, outdoor unit, nameplate, and any visible flash pattern before scheduling service.
When to stop and call GreenFlow
Call GreenFlow if the code repeats, the system is locked out, heating or cooling is not restored, there is ice buildup, electrical odor, unusual noise, or any issue involving pressure switches, sensors, wiring, refrigerant, reversing-valve operation, or warranty coverage.
Share the visible code, model and serial number if available, photos, current symptoms, and whether the issue affects heating, cooling, or both.
Showing services from our catalog
ResidentialCommercialSupport
AHRI Certificate Matching Support
Match supported indoor and outdoor equipment combinations to AHRI certification records for planning and documentation.
View service details
ResidentialRepair
Air Conditioner Blowing Warm Air
Find the cause of warm air from a central AC system and restore proper cooling where possible.
View service details
ResidentialRepair
Air Conditioner Not Cooling Repair
Diagnose an air conditioner that runs but does not provide expected cooling.
View service details
ResidentialRepair
Air Conditioner Short Cycling Repair
Diagnose frequent AC starts and stops involving airflow, controls, electrical parts, sizing, or refrigerant conditions.
View service details
ResidentialRepair
Air Conditioner Water Leak Repair
Diagnose condensate drainage, pan, coil, and pump conditions that cause water around an AC system.
View service details
ResidentialRepair
Air Conditioner Will Not Turn On
Diagnose an AC system that does not start or respond to the thermostat.
View service detailsE3.3 questions
What does E3.3 mean on a Trane S9V2 96 Two-Stage Variable Speed Gas Furnace?
The Trane S9V2 Link-enabled operation alarm table identifies E3.3 as a shorted second-stage pressure switch.
What exact Trane alarm message is tied to E3.3?
The Trane S9V2 Link-enabled operation alarm table associates E3.3 with "Shorted second-stage pressure switch".
What equipment family does this E3.3 page apply to?
This page uses the Trane S9V2 Link-enabled furnace alarm-code data set for S9V2 variable-speed gas furnaces.
What system area does E3.3 point to?
The source-backed S9V2 row groups E3.3 under pressure switch circuit.
Which Trane documentation supports this E3.3 entry?
Source-backed Trane FNR-SVN001A-EN Link-enabled furnace error-code table for S9V2 variable-speed furnaces.
Which documented alarm-code row is this page based on?
This page is based on the S9V2 row where the code is "E3.3" and the Trane alarm message is "Shorted second-stage pressure switch".
Is the alarm message wording important for E3.3?
Yes. The documented row pairs E3.3 with "Shorted second-stage pressure switch"; both the code and the message should be matched before using this page.
Does this E3.3 page cover S9V2 Link-enabled furnaces?
Yes. The source set for this record is the Trane S9V2 Link-enabled furnace alarm-code data set.
Can this E3.3 row be assumed for a different Trane product family?
No. This record is tied to the S9V2 Link-enabled furnace data set. A different Trane product family should use its own documented alarm or error-code table.
What documented system area is listed for E3.3?
The S9V2 row lists the system area for E3.3 as "Pressure switch circuit".
Does the documented system area replace diagnosis for E3.3?
No. The system area "Pressure switch circuit" organizes the documented alarm row; it does not by itself identify every jobsite cause.
What does the Trane row say about E3.3 in plain terms?
The Trane S9V2 Link-enabled operation alarm table identifies E3.3 as a shorted second-stage pressure switch.
Why is the product model shown with this E3.3 page?
The page connects the documented S9V2 alarm row to a specific stored Trane product, so the visible product model, code, and message stay together.
Is E3.3 a generic HVAC fault code?
No. The code and message on this page come from the S9V2 Link-enabled furnace alarm table, so the exact S9V2 model and displayed code should be matched to the documented row.
Should E3.3 be interpreted from the code alone?
No. The documented meaning for E3.3 should be read with the associated message "Shorted second-stage pressure switch" and the system area "Pressure switch circuit".
Does E3.3 identify the same issue as every other S9V2 alarm?
No. The S9V2 alarm table separates individual codes. This page is for E3.3, which the source-backed row defines as "Shorted second-stage pressure switch".
What should be matched before using this E3.3 page?
Match the furnace family, the visible alarm code, and the exact alarm message to the documented S9V2 row before using this page as service-prep context.
Why does this page mention pressure switch circuit?
That wording comes from the Trane S9V2 alarm-code row. It is the system area used to organize the documented E3.3 condition.
Is E3.3 related to a pressure safety condition?
The Trane source row places this code in a pressure-related system area: Pressure switch circuit. Do not treat a pressure-safety code as a thermostat-only issue.
Is E3.3 related to combustion or furnace safety controls?
The Trane source row places this code in a combustion, ignition, limit, flame, or pressure-switch safety context. These codes should be interpreted from the exact equipment board and documented flash pattern.
What information should be captured for E3.3 before clearing alerts?
Capture the exact code, any displayed alert text, the model and serial number, thermostat or control status, operating mode, symptoms, and photos of the display or LED pattern before the alert history is cleared.
Brands We Service
No matching featured brand found.