Troubleshooting code

Back to all WHK060A3**(B,E,G,K)***2 error codes

Trane WHK060A3(B,E,G,K)*2 Cooling output Pulsing troubleshooting

Cooling circuit or pressure diagnostic. Use this page to document the issue and prepare for service. GreenFlow should handle diagnosis for electrical, refrigerant, lockout, or recurring conditions.

Virtual Consultation +1 (857) 767-6414

What the code means

Cooling output Pulsing: Cooling circuit or pressure diagnostic

The Trane ReliaTel fail-code article identifies cooling output pulsing with high or low pressure switch trips or compressor/cooling-circuit conditions depending on unit configuration.

System area: ReliaTel cooling output
Service level: Call GreenFlow

Safe checks before calling

Confirm the thermostat is on, set correctly, and calling for heating or cooling.
Check the air filter and visible return-air path for obvious airflow restrictions.
Look around the outdoor unit for leaves, snow, ice, or other visible obstructions without opening the cabinet.
Take photos of the thermostat, outdoor unit, nameplate, and any visible flash pattern before scheduling service.

When to stop and call GreenFlow

Call GreenFlow if the code repeats, the system is locked out, heating or cooling is not restored, there is ice buildup, electrical odor, unusual noise, or any issue involving pressure switches, sensors, wiring, refrigerant, reversing-valve operation, or warranty coverage.

Share the visible code, model and serial number if available, photos, current symptoms, and whether the issue affects heating, cooling, or both.

ResidentialCommercialSupport

AHRI Certificate Matching Support

Match supported indoor and outdoor equipment combinations to AHRI certification records for planning and documentation.

View service details

ResidentialRepair

Air Conditioner Blowing Warm Air

Find the cause of warm air from a central AC system and restore proper cooling where possible.

View service details

ResidentialRepair

Air Conditioner Not Cooling Repair

Diagnose an air conditioner that runs but does not provide expected cooling.

View service details

ResidentialRepair

Air Conditioner Short Cycling Repair

Diagnose frequent AC starts and stops involving airflow, controls, electrical parts, sizing, or refrigerant conditions.

View service details

ResidentialRepair

Air Conditioner Water Leak Repair

Diagnose condensate drainage, pan, coil, and pump conditions that cause water around an AC system.

View service details

ResidentialRepair

Air Conditioner Will Not Turn On

Diagnose an AC system that does not start or respond to the thermostat.

View service details

Cooling output Pulsing questions

What does Cooling output Pulsing mean on a Trane WHK060A3**(B,E,G,K)***2?

The Trane ReliaTel fail-code article identifies cooling output pulsing with high or low pressure switch trips or compressor/cooling-circuit conditions depending on unit configuration.

What Trane message is associated with Cooling output Pulsing?

The Trane source used for this page associates Cooling output Pulsing with "Cooling circuit or pressure diagnostic". Match the visible display text, LED pattern, or alert wording to the exact code whenever possible.

What system area does Cooling output Pulsing point to?

This code is grouped under reliatel cooling output in the source-backed Trane troubleshooting data.

Which Trane documentation supports this Cooling output Pulsing page?

Source-backed Trane Commercial HVAC Help Center light-commercial LED code article for ReliaTel/RTRM and related rooftop control diagnostics.

Is Cooling output Pulsing related to a pressure safety condition?

The Trane source row places this code in a pressure-related system area: ReliaTel cooling output. Do not treat a pressure-safety code as a thermostat-only issue.

Is Cooling output Pulsing related to combustion or furnace safety controls?

The Trane source row places this code in a combustion, ignition, limit, flame, or pressure-switch safety context. These codes should be interpreted from the exact equipment board and documented flash pattern.

What information should be captured for Cooling output Pulsing before clearing alerts?

Capture the exact code, any displayed alert text, the model and serial number, thermostat or control status, operating mode, symptoms, and photos of the display or LED pattern before the alert history is cleared.